Datalogic QLM500 Manual de Instruções Página 133
- Página / 161
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SOFTWARE CONFIGURATION
123
8
Parameters to verify/modify:
Operating Mode Sets the parameters which customize the reader operating mode
starting from four main modes:
One Shot: acquires a single image based on the selected value for
the Acquisition Trigger and Acquisition Trigger Delay.
Continuous: continuously acquires images with a rate up to the
maximum allowable frame rate per second for the given sensor
depending on the decoding time and the Region of Interest settings.
Phase Mode: acquires images during the reading phase depending
on the selected value for the Acquisition Trigger and Acquisition
Trigger Delay. The Reading Phase-ON and Reading Phase-OFF
events mark respectively the beginning and end of the reading phase.
PackTrack: correctly assign codes read on different packs when
placed in the Reading Area at the same time.
Calibration Calibrates the acquisition parameters to maximize the reading
performance (see par. 8.4.3).
Communication Configures the parameters relative to each serial port regarding the
transmission, message formatting and string receiving.
Any change to the VisiSet™ communication port parameters (baud
rate, data bits, etc.) is effective as soon as the reader is disconnected
from VisiSet™.
Reading System Layout Allows configuring the device according to the desired layout:
Standalone, ID-NET™ or Master/Slave RS232
WebSentinel Enables the Ethernet WebSentinel Agent for communication with the
Datalogic WebSentinel™ plant array monitor.
Ethernet For 410 xxx-010 models. Sets the parameters related to the on-board
Ethernet interface and to its communication channels. Supports
application protocols: TCP/IP, EtherNet/IP, Profinet IO and Modbus
TCP.
CBX Gateway Sets the parameters related to the External Host Interface Module
through the CBX500 and to its communication channels.
Image Processing Sets the image processing parameters shared by all available
symbologies.
1D & 2D, Postal Codes
Sets the characteristics of the code symbologies to be read.
Data Collection Defines the code-collection parameters and the output message
format.
Digital I/O Configures the reader input/output parameters.
Match Code Allows setting a user-defined code and relative parameters to which
the read code will be compared (matched).
Miscellaneous Sets the reader name and the saved image format.
Symbol Verification Sets the parameters relative to the various specifications in the
Standards which regulate code validation.
LEDs And Keypad Sets the X-PRESS™ LED and Keypad parameters related to their
selected Functions: Beeper, Green Spot, Setup, Positioning, etc.
Display Sets the Display language and Layout of the BM150 Display when
using the CBX500 connection box.
Diagnostics Enables various diagnostic messages, formatting and actions.
- MATRIX 410™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- Required Accessories 12
- STEP 2 – CONNECT THE SYSTEM 13
- (polarity insensitive) 14
- RAPID CONFIGURATION 15
- STEP 4 – FOCUS THE READER 16
- Locate Function 17
- STEP 9 – TEST MODE 27
- Host Mode Programming 30
- Alternative Layouts 30
- Code Quality Verification 30
- 2 INTRODUCTION 31
- INTRODUCTION 33
- 2.3 ID-NET™ 36
- VISISET™ 40
- Restore 41
- Replacement 42
- 2.5.1 X-PRESS™ Functions 45
- Test Mode (Function 1) 46
- Focus/Locate (Function 2) 46
- Setup (Function 3) 47
- Learn (Function 4) 47
- 2.5.2 Diagnostic Indication 47
- 2.6 MODEL DESCRIPTION 48
- 2.7 ACCESSORIES 48
- 2.7.1 Lighting System Notes 50
- 2.8 APPLICATION EXAMPLES 51
- 2.8.1 Document Handling 51
- 2.8.4 Direct Part Marking 53
- 3 INSTALLATION 57
- 3.2 MECHANICAL DIMENSIONS 58
- INSTALLATION 59
- [Ø0.32] 60
- Figure 43 - Pitch angle 62
- Figure 44 - Skew angle 62
- Figure 45 - Tilt angle 62
- CBX ELECTRICAL CONNECTIONS 63
- 4.1 POWER SUPPLY 64
- 4.2 MAIN SERIAL INTERFACE 65
- 4.2.1 RS232 Interface 66
- 4.3 ID-NET™ INTERFACE 70
- 4.3.1 ID-NET™ Cables 70
- 4.3.2 ID-NET™ Response Time 71
- 4.5 INPUTS 76
- 5.1 M16 19-PIN CONNECTOR 83
- 5.4.1 RS232 Interface 86
- 5.5 ID-NET™ INTERFACE 90
- 5.5.1 ID-NET™ Cables 90
- 5.5.2 ID-NET™ Response Time 91
- 5.8 INPUTS 97
- EXTERNAL TRIGGER 98
- Matrix 410™ 98
- INPUT DEVICE 99
- 5.9 OUTPUTS 100
- USER INTERFACE 101
- MATRIX 410™ REFERENCE MANUAL 102
- 6 TYPICAL LAYOUTS 103
- 6.2 PASS-THROUGH 106
- 6.2.1 Pass-Through on RS232 106
- 6.3 ID-NET™ 108
- BA600 ID-NET™ Out 109
- BA400 Ext. Power 109
- BA500 Trigger 109
- BA300 Service 109
- Fieldbus Interface 113
- 6.4 RS232 MASTER/SLAVE 114
- 6.5 MULTIPLEXER 115
- 6.6 ETHERNET CONNECTION 116
- TYPICAL LAYOUTS 117
- 7 READING FEATURES 118
- READING FEATURES 119
- 7.2.2 1D (Linear) Codes 120
- Line Speed 125
- 8 SOFTWARE CONFIGURATION 127
- 8.2 INSTALLING VISISET™ 128
- 8.3 STARTUP 128
- 8.3.1 VisiSet™ Options 129
- 8.4 CONFIGURATION 131
- Parameters to verify/modify: 133
- SOFTWARE CONFIGURATION 135
- 8.4.3 Calibration 138
- 8.6 STATISTICS 149
- 9 MAINTENANCE 150
- 10 TROUBLESHOOTING 151
- 11 TECHNICAL FEATURES 154
- TECHNICAL FEATURES 155
- GLOSSARY 156
- UNI EN ISO 14001 160
Manuais e produtos relacionados com Leitores de códigos de barras Datalogic QLM500
(2 páginas)
(30 páginas)
(2 páginas)
(20 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais