Datalogic PowerScan D8530 Family Especificações Página 202
- Página / 244
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
POWERSCAN
™
D8330/M8300/M8300-DK
194
5.17.2 Scanner Code ID
The default Data Format is valid for all M8300 models. Code Identifer and Code len
TX (on pages 71,76 in this manual) are also valid for DK models. The item
configuration is part of the cradle configuration and is applied to the scanner system.
Optionally, the DK 16-key scanner can be set for:
• Scanner Code ID
• Scanner Code Len TX
(with the same optional values as for standard formatting)
Differently from the other DK formatting, these two configuration items have priority
over the corresponding standard formatting, and hide or substitute for them.
As a result the M8300-DK can have the following configuration scenarios:
Scanner Code ID = Disable
The settings from the standard Code ID on page 71 will be used (if programmed).
Scanner Code ID = any different value from Disable (option 1,2,3 – Datalogic
standard, AIM standard, or custom)
Use the specific DK Scanner Code ID instead of the standard Code ID. DK Scanner
Code ID will be applied and will take priority over any standard Code ID settings,
even if programmed.
5.17.3 Scanner Code Length
The behavior of Scanner Code Length is similar to that described above for Scanner
Code ID.
As a result the M8300-DK can have the following configuration scenarios:
Scanner Code Length = Disable
The settings from the standard Code Len TX on page 76 will be used (if
programmed).
Scanner Code Length = any different value from Disable (variable digit format,
fixed digit format)
Use the specific DK Scanner Code Length instead of the standard Code Len TX.
Scanner Code Length will be applied and will take priority over any standard Code
Len TX settings, even if programmed.
NOTE: Both of these configuration items are part of the scanner configuration but are
applied to the whole system. The configuration item overwrites the default Data
Format .
- PowerScan 1
- M8300/M8300-DK 1
- Datalogic ADC, Inc 2
- ©2007-2014 Datalogic, Inc 2
- CONTENTS 3
- GENERAL VIEW 7
- Figure C – BC-8000 8
- Figure D – C-8000 8
- 1 INTRODUCTION 9
- 2 INSTALLATION 10
- 2.3 RS-232 CONNECTION 13
- 2.4 USB 13
- 2.5 IBM USB POS 14
- 2.6 WEDGE CONNECTION 15
- 2.8 NETWORK CONNECTIONS 16
- 2.8.2 Network Cabling 17
- No Termination 18
- 2.9 POWERSCAN 19
- M8300 BATTERY MAINTENANCE 19
- 2.9.1 Battery Charging 19
- 2.9.2 Replacing PowerScan 19
- M8300 Batteries 19
- POWERSCAN 20
- D8330/M8300/M8300-DK 20
- 2.10.1 Desktop Mounting 21
- Portable Desktop Use 22
- Fixed Desktop Use 22
- 2.10.2 Wall Mounting 24
- 3 POWERSCAN 26
- M8300 SYSTEM AND NETWORK 26
- LAYOUTS 26
- 3.1.4 C-BOX Layout 28
- 3.2.1 Host Master Layout 29
- 3.2.2 BC-8060 Master Layout 30
- /*32: FAIL*/ 31
- 4 CONFIGURATION 32
- 4.2 SETUP PROCEDURES 33
- Ì$+$*oÎ 34
- ÌIB'Î 35
- ÌRA0RFHÎ 36
- Ì$+RN0$-IÎ 36
- Ì$+RX0$-qÎ 37
- Ì$+RN1$-NÎ 37
- 4.5.2 PowerScan 38
- 4.6 POWERSCAN 39
- M8300/STAR-SYSTEM™ SETUP 39
- Ì$+RF4Î 41
- Ì$+RZ2$-ÇÎ 42
- Ì$+RZ1$-~Î 42
- Ì$+CP0$-$Î 43
- Ì$+CM2EC0$->Î 43
- Ì$+CM1$-ÈÎ 43
- Ì$+CM0$-ÃÎ 43
- Ì$+CP6$-BÎ 43
- KEY TRANSMISSION MODE 44
- KEYBOARD TYPE 44
- Ì$+CP507$-+Î 45
- Ì$+CP508$-2Î 45
- Ì$+CP512$-uÎ 45
- First Start-Up 46
- D8330/M8300 48
- RS-232 PARAMETERS 49
- BAUD RATE 50
- DATA BITS 51
- STOP BITS 51
- HANDSHAKING 51
- ACK/NACK PROTOCOL 52
- INTER-CHARACTER DELAY 52
- RX TIMEOUT 53
- SERIAL TRIGGER LOCK 53
- USB PARAMETERS 54
- USB-COM 56
- USB-KBD 57
- KEYBOARD NATIONALITY 57
- INTER-CODE DELAY 59
- USB KEYBOARD SPEED 59
- WEDGE PARAMETERS 60
- CAPS LOCK 62
- NUM LOCK 63
- KEYBOARD SETTING 64
- CONTROL CHARACTER EMULATION 66
- PEN EMULATION 67
- OPERATING MODE 68
- MINIMUM OUTPUT PULSE 69
- OVERFLOW 70
- OUTPUT LEVEL 71
- IDLE LEVEL 71
- INTER-BLOCK DELAY 71
- NETWORK PARAMETERS 72
- RS-485 NETWORK 73
- NETWORK BAUD RATE 73
- SLAVE ADDRESS RANGE 74
- NETWORK WARNING MESSAGE 74
- RECEPTION WARNING MESSAGE 74
- MASTER CRADLE HEADER 75
- MASTER CRADLE TERMINATOR 76
- CODE IDENTIFIER 79
- CUSTOM CODE IDENTIFIER 79
- SPECIAL KEYS 82
- FIELD ADJUSTMENT 83
- FIELD ADJUSTMENT CHARACTER 84
- CODE LENGTH TX 84
- CHARACTER REPLACEMENT 85
- POWER SAVE 89
- SLEEP STATE 90
- ENTER SLEEP TIMEOUT 90
- READING PARAMETERS 91
- TRIGGER TYPE 92
- TRIGGER SIGNAL 92
- TRIGGER CLICK 92
- TRIGGER-OFF TIMEOUT 93
- FLASH MODE 93
- READS PER CYCLE 93
- SAFETY TIME 94
- BEEPER INTENSITY 94
- BEEPER TONE 95
- BEEPER TYPE 95
- BEEPER LENGTH 95
- GOOD READ SPOT DURATION 96
- AIMING SYSTEM 96
- CRADLE BEEPER INTENSITY 96
- DECODING PARAMETERS 97
- INK SPREAD 98
- OVERFLOW CONTROL 98
- INTERDIGIT CONTROL 98
- DECODING SAFETY 99
- PUZZLE SOLVER™ 99
- CODE SELECTION 100
- Ì#+AUTOWÎ 101
- EAN/UPC FAMILY 103
- ÌAA8Ad03Î 104
- ÌAA8Ad19Î 104
- 2/5 FAMILY 109
- CODE 39 FAMILY 110
- CODE 128 FAMILY 111
- CODE 93 112
- CODABAR FAMILY 112
- CODE 11 115
- CODE 16K 116
- CODE 49 116
- GS1 DATABAR™ CODES 117
- ADVANCED FORMATTING 118
- CONCATENATION 119
- RADIO PARAMETERS 137
- RADIO PROTOCOL TIMEOUT 138
- RADIO RX TIMEOUT 138
- POWER-OFF TIMEOUT 139
- TRANSMISSION MODE 139
- SINGLE STORE 141
- BATCH MODE 142
- FIND ME 142
- DISPLAY and KEYPAD 143
- PARAMETERS 143
- (3-Key Model) 143
- DISPLAY PARAMETERS 144
- 3-KEY MODEL PARAMETERS 145
- DISPLAY-OFF TIMEOUT 145
- DISPLAY MODE 145
- KEYPAD PARAMETERS 146
- (16-Key Model) 147
- 16-KEY DK MODEL PARAMETERS 149
- KEY PRESS SOUND 149
- FUNCTION KEY PROGRAMMING 149
- STRING TABLE 150
- FUNCTION KEY LABEL 151
- LOWER CASE 151
- SHIFT KEY PROGRAMMING 152
- LAST CODE SHOWN TIMEOUT 154
- BACKLIGHT 155
- SCREEN REFRESH 155
- DATA FORMAT 156
- TERMINATOR 158
- SCANNER CODE ID 161
- SCANNER CODE LENGTH 161
- OPERATIVE MODE 162
- QTY/CODE MODE 163
- QTY/CODE SEND MODE 164
- REPEAT TIMEOUT 165
- QTY/CODE SEPARATOR 166
- APPEND CODE 167
- 5 REFERENCES 168
- 5.1.2 ACK/NACK Protocol 169
- 5.1.3 FIFO 170
- 5.1.4 RX Timeout 171
- 5.2 PEN PARAMETERS 171
- 5.2.1 Minimum Output Pulse 171
- 5.2.3 Overflow 172
- 5.2.5 Inter-Block Delay 173
- 5.3 NETWORK PARAMETERS 173
- 5.4 DATA FORMAT 174
- Enter Configuration 176
- Exit and Save Configuration 176
- REFERENCES 179
- ÌFQ9C2>Î 181
- 5.4.3 Address Stamping 183
- 5.4.4 Address Delimiter 183
- 5.4.5 Time Stamping Format 184
- 5.5 POWER SAVE 184
- 5.5.1 Sleep State 184
- 5.6.5 Safety Time 186
- 5.7 DECODING PARAMETERS 186
- 5.7.1 Ink-Spread 186
- 5.7.2 Overflow Control 186
- 5.7.3 Interdigit Control 187
- 5.8 ADVANCED FORMATTING 187
- 5.8.1 Match Conditions 187
- 5.9.2 Radio RX Timeout 188
- 5.9.3 Power-Off Timeout 188
- 5.9.4 Transmission Mode 189
- 5.9.6 Single Store 190
- 5.9.7 Batch Mode 190
- 5.9.8 Find Me (PowerScan 192
- M8300 only) 192
- 5.10.1 Display Mode 193
- Ì$+$0ÂÎ 195
- Ì$+$1$Î 195
- Ì#+CODEÂÎ 195
- Ì$+ZZ0$-*Î 196
- Ì$+ZZ2$-4Î 197
- Ì$+ZZ3$-9Î 198
- Ì$+RN2$-SÎ 200
- MESSAGE FORMATTING 201
- 5.17.2 Scanner Code ID 202
- 5.17.3 Scanner Code Length 202
- 6 MESSAGE FORMATTING 203
- 6.3.1 Cursor Control 207
- 6.3.2 Font Selection 207
- 6.3.3 Clearing Display 207
- 6.3.5 Setting RTC 208
- 7 TECHNICAL FEATURES 211
- 7.2 POWERSCAN 212
- 7.3 POWERSCAN 213
- M8300-DK 16-KEY MODEL 213
- Environmental Features 214
- Mechanical Features 214
- 7.4 BC-80X0 / C-8000 215
- 7.6 STATUS INDICATORS 216
- 7.7 READING TABLES 219
- Exit and Save configuration 220
- SERIAL CONFIGURATION STRINGS 221
- (not for USB-KBD-ALT-MODE) 223
- (IBM AT compatible only) 223
- (only for D8330 series) 228
- B CODE IDENTIFIER TABLE 237
- C HEX AND NUMERIC TABLE 240
- HEX / NUMERIC TABLE 241
Manuais e produtos relacionados com Leitores de códigos de barras Datalogic PowerScan D8530 Family
(28 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.260 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais