Datalogic DS6300-100-011 Manual de Instalação Página 39
- Página / 129
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CBX ELECTRICAL CONNECTIONS
23
3
3.2.1 RS232 Interface
The main serial interface is used in this case for point-to-point connections; it handles
communication with the host computer and allows both transmission of code data and the
programming of the scanner. This is the default setting.
The following pins are used for RS232 interface connection:
CBX100/500
Function
TX Transmit Data
RX Receive Data
RTS Request To Send
CTS Clear To Send
SGND Signal Ground
It is always advisable to use shielded cables. If the shield is tied to ground at the Host, then
leave it floating at the CBX. If it is floating at the Host then tie it to Shield at the CBX. The
overall maximum cable length must be less than 15 m (50 ft).
SGND RXD TXD
CTS RTS
USER INTERFACE
SGND TX RX
RTS CTS
SCANNER
Figure 24 – RS232 Main Interface Connections Using Hardware Handshaking
START
OF
TRANSMISSION
END
OF
TRANSMISSION
+ V
RTS
- V
+ V
TX DATA
- V
+ V
CTS
- V
DATA
TRANSMISSION
DATA
TRANSMISSION
C1
C2
C4
C3
C5
TRANSMISSION
STOPPED
ENABLED
DISABLED
ENABLED
IDLE
IDLE
Figure 25 - RS232 Control Signals
The RTS and CTS signals control data transmission and synchronize the connected devices.
If the RTS/CTS handshaking protocol is enabled, the DS6300 activates the RTS output to
indicate a message is to be transmitted. The receiving unit activates the CTS input to enable
the transmission.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- POWER SUPPLY 8
- CE COMPLIANCE 9
- FCC COMPLIANCE 9
- GENERAL VIEW 10
- Laser Safety Label 11
- Laser Beam Output Window 11
- GUIDE TO INSTALLATION 14
- 1 INTRODUCTION 17
- 1.2 APPLICATIONS 18
- DS6300 - 10X - 0YY 19
- INTRODUCTION 21
- 1.5 INDICATORS 22
- 1.6 KEYPAD AND DISPLAY 22
- 1.6.1 Internal Net 22
- 1.6.2 Test Mode 23
- 1.7 ACCESSORIES 23
- 2 INSTALLATION 25
- 2.2 MECHANICAL MOUNTING 26
- 2.2.1 Mounting the Scanner 26
- INSTALLATION 29
- 2.3 POSITIONING THE SCANNER 33
- 2.3.1 16° Skew Positioning 34
- 2.3.2 45° Skew Positioning 35
- CBX ELECTRICAL CONNECTIONS 37
- 3.1 POWER SUPPLY 38
- 3.2 MAIN SERIAL INTERFACE 38
- 3.2.1 RS232 Interface 39
- Function 40
- Multidrop Cable 42
- Reference 43
- USER INTERFACE 43
- 3.4 INPUTS 44
- MEP-593 PH-1 Photocell (PNP) 45
- External Device 47
- Power Reference 47
- 3.4.1 Code Verifier 48
- 3.5 OUTPUTS 48
- 3.6 USER INTERFACE - HOST 51
- 4.1 POWER SUPPLY 54
- 4.2 MAIN SERIAL INTERFACE 54
- E XTE RN AL TRIGGE R/E NCODE 61
- 4.4.1 Code Verifier 62
- 4.5 OUTPUTS 62
- 00 USER INTERFACE 63
- 4.6 USER INTERFACE 64
- 5 LONWORKS CONNECTIONS 65
- 5.1 NETWORK TERMINATION 66
- 5.2 LONWORKS INTERFACE 66
- LONWORKS CONNECTIONS 67
- 6 FIELDBUS CONNECTIONS 69
- FIELDBUS CONNECTIONS 71
- 6.3 DEVICENET INTERFACE 72
- 6.4 PROFIBUS INTERFACE 73
- 7 TYPICAL LAYOUTS 74
- TYPICAL LAYOUTS 75
- 7.1.2 Multidata Network 77
- 7.1.3 Fieldbus Networks 78
- 8 SOFTWARE CONFIGURATION 80
- Test Operating Mode 81
- On Line Operating Mode 82
- Automatic Operating Mode 82
- SOFTWARE CONFIGURATION 83
- Net-Autoset 85
- Express Network Setup 85
- Network Wizard 86
- 8.4 PARAMETER DEFAULT VALUES 91
- 9 READING FEATURES 95
- 9.3 PERFORMANCE 98
- 9.3.1 Reading Conditions 98
- 9.4 READING DIAGRAMS 100
- 9.4.1 DS6300 Standard Model 100
- READING FEATURES 101
- DS6300 REFERENCE MANUAL 102
- 9.4.3 DS6300 with GFX-60 108
- 10 MAINTENANCE 110
- MAINTENANCE 111
- 11 TROUBLESHOOTING 112
- 12 TECHNICAL FEATURES 115
- Main Serial Interface 117
- Fieldbus 118
- Network 118
- ALTERNATIVE LAYOUTS 119
- PASS THROUGH 120
- RS232 MASTER/SLAVE 121
- MULTIPLEXER 123
- GLOSSARY 124
- DECLARATION OF CONFORMITY 128
Manuais e produtos relacionados com Leitores de códigos de barras Datalogic DS6300-100-011
(48 páginas)
(24 páginas)
Remko PWW 5000 manuels
Manuels d'utilisation et guides de l'utilisateur pour Radiateurs Remko PWW 5000.
Nous fournissons des manuels en pdf 3 Remko PWW 5000 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais