Datalogic DX8200A-3010 Manual de Instalação Página 103
- Página / 139
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
READING FEATURES
87
9
Auto PackTrack Setup
1. Click on the Start button and follow the instructions given in the Auto PackTrack
procedure window.
The first message is sent to the slaves and their status is shown in the synoptic buttons
at the top of the window.
The scanner status indicated by each synoptic button has the following convention:
Color Symbol Meaning
Grey
xx-U
slave xx cannot be calibrated - calibration is not supported by scanner
software version
Red
xx-U
slave xx can be calibrated but the calibration procedure fails either barcode
reading or verification
Red
xx-L
slave xx can be calibrated - is Lost stops responding during the procedure
Aqua
xx-I
slave xx can be calibrated - is in the Initial state ready to be calibrated
Yellow
xx-N
slave xx can be calibrated - is calibrated but Not verified
Green
xx-C
slave xx calibrated - is calibrated and verified
The symbol xx is the number of the slave scanner 01, 02, 03 etc.
2. Follow each step given in the Auto PackTrack procedure window. The instructions and
summary of each step are written in the terminal area of the window. The Synoptic
buttons report the slave scanner status throughout the procedure.
Basically, place the PCT-8000 onto the moving conveyor, before the PS Line (reference
point) and parallel to a conveyor edge (i.e. right-hand edge) with its arrow in the same
direction as the conveyor movement. Let it pass through the reading station.
NOTE
If there are any nodes that show as U or L, then you should Stop the
procedure and correct the problem. If the nodes respond with I, N, or C then
you can Continue with the procedure.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- POWER SUPPLY 8
- CE COMPLIANCE 9
- FCC COMPLIANCE 9
- GENERAL VIEW 10
- GUIDE TO INSTALLATION 13
- 1 INTRODUCTION 17
- DX8200A - 3 X Y Z 19
- 1.5 KEYPAD AND DISPLAY 20
- 1.5.1 Internal Net 20
- 1.5.2 Test Mode 21
- 1.5.3 PackTrack (Auto) 21
- USING SCANNER MENU 22
- 1.6.3 Auto PackTrack Setup 24
- INTRODUCTION 25
- 1.7 ACCESSORIES 27
- Fieldbus) 28
- 2 INSTALLATION 29
- 2.2 MECHANICAL MOUNTING 30
- 2.2.1 Mounting the Scanner 30
- INSTALLATION 31
- CBX ELECTRICAL CONNECTIONS 33
- 3.1 POWER SUPPLY 34
- 3.2 MAIN SERIAL INTERFACE 35
- Function 36
- Multidrop Cable 39
- Reference 40
- USER INTERFACE 40
- MEP-593 PH-1 Photocell (PNP) 42
- OEK-1 Encoder (PNP) 43
- In put De vi ce (Enc oder) 43
- 9-pin male connector 48
- 25-pin male connector 48
- 4.1 POWER SUPPLY 50
- 4.2 MAIN SERIAL INTERFACE 51
- 4.2.1 RS232 Interface 52
- 4.3 AUXILIARY INTERFACE 56
- 4.4 INPUTS 56
- EXTERNAL TRIGGER/ENCODER 57
- 4.4.1 Code Verifier 59
- 4.5 OUTPUTS 59
- DX8200A USER INTERFACE 60
- 4.6 USER INTERFACE 61
- 5 LONWORKS CONNECTIONS 62
- 5.1 NETWORK TERMINATION 63
- 5.2 LONWORKS INTERFACE 64
- LONWORKS CONNECTIONS 65
- 6 FIELDBUS CONNECTIONS 66
- FIELDBUS CONNECTIONS 67
- 6.3 DEVICENET INTERFACE 69
- 6.4 PROFIBUS INTERFACE 70
- 7 TYPICAL LAYOUTS 71
- TYPICAL LAYOUTS 73
- Minimum Distance 75
- 7.1.3 Redundant System 76
- 7.1.4 Multidata Network 78
- 7.1.5 Fieldbus Networks 79
- 8 SOFTWARE CONFIGURATION 81
- Test Operating Mode 82
- On Line Operating Mode 83
- Automatic Operating Mode 83
- Net-Autoset 86
- Express Network Setup 86
- Network Wizard 87
- SOFTWARE CONFIGURATION 89
- 8.4 PARAMETER DEFAULT VALUES 92
- 9 READING FEATURES 97
- 9.2 PACKTRACK™ 98
- PackTrack™ Reference System 99
- DX8200A REFERENCE MANUAL 100
- READING FEATURES 101
- Auto PackTrack Setup 103
- Auto PackTrack Report 106
- Scanner Direction 108
- PS Offset 109
- 9.3 PERFORMANCE 112
- 9.3.1 Reading Conditions 113
- 9.4 READING DIAGRAMS 115
- 10 MAINTENANCE 119
- 11 TROUBLESHOOTING 121
- 12 TECHNICAL FEATURES 124
- TECHNICAL FEATURES 125
- A ALTERNATIVE LAYOUTS 126
- Fieldbus 127
- Network 127
- PASS THROUGH 129
- RS232 MASTER/SLAVE 130
- MULTIPLEXER 132
- GLOSSARY 133
- DECLARATION OF CONFORMITY 138
Manuais e produtos relacionados com Leitores de códigos de barras Datalogic DX8200A-3010
(2 páginas)
(20 páginas)Remko PWW 4000 manuels
Manuels d'utilisation et guides de l'utilisateur pour Radiateurs Remko PWW 4000.
Nous fournissons des manuels en pdf 2 Remko PWW 4000 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais