Datalogic Magellan 3300HSi Manual de Instruções Página 12
- Página / 208
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Getting Started
4
Magellan
TM
3300HSi
Error Codes
If an error is detected, the scanner will sound a long low tone (for three seconds) and flash its
LED, indicating a failure. When this occurs, remove the top cover and press the Scanner Push
Button to hear the error code. If it is configured to do so, the scanner will sound a series of beeps
corresponding to the error code and/or flash its LED simultaneous to the beeps. The table
below describes what these codes mean and what action should be taken for each.
NUMBER OF
LED
FLASHES/
BEEPS
ERROR CORRECTIVE ACTION
1 Configuration Contact Helpdesk for assistance
2 Interface PCB
6 Main PCB
10 Button Error
12 Imager Module
13 Software ID Failure
14 Software Fatal Fault
Installation
For comfortable slide-through scanning, mount the scanner level with the countertop. Follow
these steps for flush installation:
1. Decide the best situation for the scanner by considering...
• Proximity to the user. Verify that checkstand features allow the scanner to be within
eas
y reach of the user, without interfering with cash drawers or other equipment.
• Cable routing to and from the scanner: Can cables an
d connected devices be routed in
such a way as to be protected from damage or tampering?
• Mounting stability. Avoid placing the scan
ner in such a way as to subject it to excess
vibration, bumping, spillage, etc.
• Peripheral connections from the scanner
, such as a handheld device.
2. The countertop must be modified to accept the scanner. At the time of this writing, three
options ar
e available.
•
Figure 3a shows the dimensions for the opening and other details if a shelf is to be built
to support the unit.
•
Figure 3b details the cutout dimensions if an adapter fixture holding the scanner will
rest with its rim above the countertop.
•
Figure 3c provides dimensions if an adapter fixture holding the scanner will be recessed
to be flush with the countertop.
3. Remove the Connector Cover, then connect and route the cables at the scanner.
4. Seat the scanner or in the countertop opening (or adapter).
5. Switch the terminal OFF.
- Magellan 1
- 3300HSi 1
- Product Reference Guide 1
- Table of Contents 3
- 3200VSi 4
- Product Reference Guide 3 5
- Chapter 1 9
- Getting Started 9
- Connecting the Scanner 10
- Error Codes 12
- Installation 12
- 5 13
- Figure 3. Countertop Cutouts 13
- LED and Beeper Indicators 14
- Programming 16
- Bar Code Mask 17
- LED Class 18
- Chapter 2 19
- General Features 19
- Composite label 21
- Scanner Button Options 22
- Camera Button Mode 23
- LED Level 24
- Auxiliary Port Mode 25
- Auxiliary Port Baud Rate 26
- START / END 27
- PROGRAMMING bar codes 27
- Sleep Mode 28
- Sleep Mode — cont 29
- Wake Up Intensity 30
- Wake Up Intensity — cont 31
- ERI Timeout 33
- Good Read: When to Indicate 34
- Good Read Beep Control 35
- Good Read Beep Frequency 35
- Good Read Beep Length 36
- Good Read Beep Volume 37
- Cell Phone Mode 38
- Chapter 3 39
- Image Capture 39
- Image Compression 42
- Image Format 42
- Image Size 43
- Image Brightness 44
- Image Contrast 44
- Chapter 4 45
- Interface Related Features 45
- Interface Selection 47
- Interface Selection — cont 48
- Interface Features 49
- Interface Features — cont 50
- RS-232 Interface Features 51
- Hardware Flow Control 53
- Intercharacter Delay 54
- Intercharacter Delay — cont 55
- Software Flow Control 55
- Host Echo 56
- Host Echo Quiet Interval 57
- Signal Voltage: Normal/TTL 58
- RS-232 Invert 59
- Beep on ASCII BEL 59
- Beep on Not on File 60
- ACK NAK Options 61
- ACK Character 62
- NAK Character 62
- Retry on ACK NAK Timeout 63
- ACK NAK Timeout Value 63
- ACK NAK Retry Count 64
- ACK NAK Error Handling 65
- Single Cable RS-232 66
- 59 67
- RTS CTS Selection = 67
- Single Cable RS-232 Use BCC 68
- Single Cable RS-232 Use STX 69
- Single Cable RS-232 Use ETX 70
- Single Cable Pacesetter Plus 71
- USB-OEM Interface Features 72
- Keyboard Wedge 73
- USB Keyboard 73
- Keyboard Wedge — cont 74
- 69 77
- Control Characters 77
- Disable Control Characters 77
- USB COM Interface Set-up 79
- Chapter 5 81
- Data Editing 81
- Label ID — cont 85
- Case Conversion 90
- Character Conversion 91
- Chapter 6 93
- UPC-A — continued 94
- Disable/Enable UPC-E 96
- UPC-E — continued 97
- Expand UPC/EAN to GTIN 99
- Disable/Enable EAN-13 100
- Check Digit Transmission 100
- EAN-13 — continued 101
- Disable/Enable EAN-8 102
- EAN-8 — continued 103
- EAN Two-Label 104
- Price Weight Check Digit 105
- Symbologies 106
- Add-ons — continued 107
- UCC/EAN 128 Emulation 108
- GS1-128 Emulation 109
- Length Control 110
- Coupon Read Control 111
- GS1 DataBar Limited 112
- Disable/Enable Code 39 113
- Check Character Calculation 113
- Check Character Transmit 114
- Start/Stop Characters 114
- Code 39 Full ASCII 115
- Code 39 — continued 116
- Code 32 Italian Pharmacode 117
- Code 128 119
- Code 128 — continued 120
- Interleaved 2 of 5 122
- Check Digit Calculation 123
- Check Digit Transmit 123
- Disable/Enable Codabar 125
- Check Character Verification 125
- Codabar — continued 127
- Start/Stop Character Match 129
- Disable/Enable Code 93 129
- Code 93 — continued 130
- Disable/Enable MSI 131
- MSI Check Character Transmit 131
- MSI — continued 132
- 2D Symbologies 135
- Disable/Enable PDF 417 136
- PDF 417 — continued 137
- Micro PDF 417 139
- Micro PDF 417 — continued 140
- Datamatrix 142
- Datamatrix — continued 143
- Disable/Enable QR Code 145
- QR Code — continued 146
- Maxicode 148
- Maxicode — continued 149
- Disable/Enable Aztec 151
- Aztec — continued 152
- Composite Labels 154
- 147 155
- Advanced Decoding Features 157
- UPC/EAN Quiet Zone 158
- Chapter 9 159
- References 159
- Global Prefix/Suffix 160
- Label ID 161
- Appendix A 163
- Product Specifications 163
- Physical Properties 164
- Electrical Parameters 164
- Environmental Parameters 164
- Other Parameters 164
- Appendix B 165
- Cable Pinouts 165
- Appendix C 167
- Alpha-Numeric Pad 167
- Appendix D 169
- Factory Default Settings 169
- Appendix E 175
- 171 179
- Table 6 179
- Table 7 180
- Japanese DOS Function Key Map 180
- 173 181
- Appendix F 183
- Host Commands 183
- Appendix G 185
- Sample Symbols 185
- 1D Symbol Samples — continued 186
- 2D Sample Symbols 187
- Composite Sample Symbols 188
- Appendix H 189
- Autorun File Processing 190
- From Scanner to microSD Card 191
- From microSD Card to Scanner 192
- 185 193
- By Autorun file 193
- Appendix I 195
- 189 197
- 191 199
- Code 39-Pharmacode 200
- I 2 of 5 200
- AIM Formats 203
- 5-Digit Supplemental 204
- Code 128 Supplemental 204
- Bookland 204
- RSS Expanded 205
- Code 128 / EAN128 206
- ASCII Character Set 207
- Datalogic ADC, Inc 208
Manuais e produtos relacionados com Leitores de códigos de barras Datalogic Magellan 3300HSi
(24 páginas)
(94 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais