Datalogic C-BOX 200 Manual de Instalação

C-BOX 200Installation Manual

viii

GENERAL FEATURES111 GENERAL FEATURES1.1 DESCRIPTIONThe C-BOX 200 is a connection box which can be used as an accessory of theDatalogic scanners to per

C-BOX 200222 INSTALLATION2.1 PACKAGE CONTENTSVerify that the C-BOX 200 and all the parts supplied with the equipment are presentand intact when openin

INSTALLATION322.2 OPENING THE DEVICETo install the C-BOX 200 or during normal maintenance, it is necessary to open it byunscrewing the four cover scr

C-BOX 200422.3 MECHANICAL INSTALLATIONThe diagram below gives the overall dimensions of the C-BOX 200 and may be usedfor its installation.mminC-BOXFig

INSTALLATION52C-BOX 200 can be installed to operate in different positions. The two screw holesinside the housing of the C-BOX 200 are for mechanical

C-BOX 200622.4 ELECTRICAL CONNECTIONS AND SETUPThe following figure shows the typical layout. The dotted line in the figure refers to anoptional hard

INSTALLATION722.4.1 Power SupplyPower is supplied to the C-BOX 200 through the pins provided on the spring clampconnector.The power switch (see Figure

C-BOX 200822.4.2 System WiringThe connection and wiring procedure for C-BOX 200 is described as follows:1) Open the C-BOX 200 as described in paragra

INSTALLATION92The C-BOX 200 spring clamp connector pinouts are indicated in the following table.Refer to the scanner Installation Manual for details.P

C-BOX 200Installation Manual

C-BOX 2001022.4.3 Chassis Grounding Jumper SettingsThe scanner chassis grounding method can be selected by positioning a jumper (seeFigure 9). In thi

INSTALLATION1122.4.4 Multidrop Address SelectionFor RS485 half-duplex interface connections, the scanner multidrop address shouldbe set using the rota

C-BOX 2001222.4.5 RS485 Bus TerminationONS2OFFFigure 11 - Termination resistance switchThe switch S2 enables or disables the insertion of the bus ter

INSTALLATION1322.4.6 Connection to a MultiplexerThe following figure shows a multidrop layout with C-BOX 200 devices connected toa Multiplexer:MULTIP

C-BOX 2001422.4.7 OM4000 Jumper SettingsJ1 J2Figure 13 - OM4000 jumpersThe jumpers allow connection to the EXT TRIG signals on separate spring clampt

INSTALLATION1522.5 9-PIN SCANNER AUXILIARY SERIAL INTERFACEThe scanner auxiliary serial interface available on the internal 9-pin connector can beuse

C-BOX 2001622.6 SCANNER REQUIREMENTS1) The C-BOX 200 can be connected to the following scanners through the 25-pinconnector illustrated in Figure A.D

INSTALLATION1722.7.1 GET/SEND ButtonsThe C-BOX 200 has two internal function buttons (GET, SEND). The procedure toenable the GET/SEND function is the

C-BOX 2001822.7.2 LED IndicatorsPower onWarningTxFigure 15 - LED IndicatorsThe three internal LEDs of the C-BOX 200 (see Figure 15) indicate the follo

TECHNICAL FEATURES1933 TECHNICAL FEATURESELECTRICAL FEATURESPowerSupply voltage 10 to 30 VdcPower consumption max. 1.4 W + scannerUSER INTERFACELED

C-BOX 200INSTALLATION MANUAL

01DATALOGIC S.p.A.,Via Candini, 240012 - Lippo di CalderaraBologna - Italydichiara chedeclares that thedéclare que lebescheinigt, daß das Gerätdeclar

DATALOGIC S.p.A.Via Candini 240012 - Lippo di Calderara di RenoBologna - ItalyC-BOX 200Ed.: 01/2002ALL RIGHTS RESERVEDDatalogic S.p.A. reserves the ri

iiiCONTENTSGUIDE TO INSTALLATION ...ivGENERAL VIEW ...

ivGUIDE TO INSTALLATIONThe following can be used as a checklist to verify all of the steps necessary forcomplete installation of the C-BOX 200.1) Rea

vGENERAL VIEWC-BOX 200123Figure A25-pin scanner connectorCover screws (4)Compression connectors123

viC-BOX 20041012 67 8 9 125311Figure BPower switch (ON/OFF)12Spring clamp terminal blocks3Multidrop address switches54Power on LEDWarning LED6Tx LED7G

viiSAFETY PRECAUTIONSPOWER SUPPLYATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT- This product is intended to be installed by Qualified