Datalogic DS4300 Manual de Instalação

C-BOX 100Installation Manual

viii

GENERAL FEATURES 1 1 1 GENERAL FEATURES 1.1 DESCRIPTION The C-BOX 100 is a connection box which can be used as an accessory of the Datalogic scann

C-BOX 100 2 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 100 and all the parts supplied with the equipment are present and intact

INSTALLATION 3 2 2.2 OPENING THE DEVICE To install the C-BOX 100 or during normal maintenance, it is necessary to open it by unscrewing the four co

C-BOX 100 4 2 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimensions of the C-BOX 100 and may be used for its installation.

INSTALLATION 5 2 C-BOX 100 can be installed to operate in different positions. The two screw holes inside the housing of the C-BOX 100 are for mechan

C-BOX 100 6 2 2.4 ELECTRICAL CONNECTIONS AND SETUP The following figure shows the typical layout. The dotted line in the figure refers to an optio

INSTALLATION 7 2 2.4.1 Power Supply Power is supplied to the C-BOX 100 through the pins provided on the spring clamp connector. The power switch (s

C-BOX 100 8 2 2.4.2 System Wiring The connection and wiring procedure for C-BOX 100 is described as follows: 1) Open the C-BOX 100 as described in

INSTALLATION 9 2 Pin Name 1, 3, 5 VS 2, 4, 6 GND 7, 8 EARTH GROUND *9, 13 RS485 CABLE SHIELD 20, 40 RESERVED 35 TX AUX 37 RX AUX DS2100 DS2400

C-BOX 100Installation Manual

C-BOX 100 10 2 NOTE Grounding varies according to the scanner connected to the C-BOX 100: - for DS2XXX scanners, pins 10, 14 and 19 (SGND MAIN) a

INSTALLATION 11 2 2.4.4 Scanner Selection The following figure indicates the correct switch position for each type of scanner. ADS1100 DS2200 Othe

C-BOX 100 12 2 2.4.6 OM4000 Jumper Settings J1J2 Figure 12 - OM4000 Jumpers These jumpers allow connection to the EXT TRIG signals on separate s

INSTALLATION 13 2 2.5 9-PIN SCANNER AUXILIARY SERIAL INTERFACE The scanner auxiliary serial interface available on the internal 9-pin connector can

C-BOX 100 14 3 3 TECHNICAL FEATURES ELECTRICAL FEATURES Power Supply voltage 10 to 30 Vdc* Power consumption 0.5 W + scanner power consumption

01 DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das G

C-BOX 100 INSTALLATION MANUAL

DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy C-BOX 100 Ed.: 09/2003 ALL RIGHTS RESERVED D

iii CONTENTS GUIDE TO INSTALLATION ... iv GENERAL VIEW ...

iv GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the C-BOX 100

v GENERAL VIEW C-BOX 100 213 Figure A 25-pin scanner connectorCover screws (4)Compression connectors123

vi C-BOX 100 Figure B Power switch (ON/OFF) 1 2 Chassis grounding selector 3 20 mA C.L. connector 5 4 Power on LED (green) Power Polarity Er

vii SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT - This product is intended to be installed b