Datalogic CBX800 Manual de Instalação

CBX800 INSTALLATION MANUAL Figure A Indicator LEDs 1 Cover Screws (4) 2 Compression Connectors (5) 425-pin Device Connector 5Host Inte

CBX800 INSTALLATION MANUAL 10 The input power signals Vdc, GND and Earth as well as the network signals REF, ID+, ID- and Shield; and RTX+, RTX-

CBX800 INSTALLATION MANUAL 11 SOURCE CHASSIS GROUNDING JUMPER SETTINGS The reading device chassis grounding method can be selected by positioning a

CBX800 INSTALLATION MANUAL 12 RS485 HD OFF ON Figure 11 – RS485 HD Termination Resistance Switch The RS485 HD termination resistance swit

CBX800 INSTALLATION MANUAL 13 The Net Type selector switch allows setting the Gateway type: Serial (None), Fieldbus, ID-NET™ network:  all non netwo

CBX800 INSTALLATION MANUAL 14 ELECTRICAL CONNECTIONS POWER SUPPLY CBX00 can accept power from the connected reading device through the 25-pin con

CBX800 INSTALLATION MANUAL 15 Host RS232 Interface The RS232 interface can be used for connections to the host computer allowing transmission of cod

CBX800 INSTALLATION MANUAL 16 Host RS485 Full-Duplex Interface The RS485 full-duplex (5 wires + shield) interface is used for non-polled communicat

CBX800 INSTALLATION MANUAL 17 Host RS485 Half-Duplex Interface The RS485 half-duplex (3 wires + shield) interface is used for polled communication p

CBX800 INSTALLATION MANUAL 18 AUXILIARY INTERFACE All CBX800s have an RS232 auxiliary interface available on the 9-pin connector below, which can b

CBX800 INSTALLATION MANUAL 19 DATA SOURCE INTERFACE The Data Source port can be used for configuration and data monitoring purposes. It allows full

CBX800 INSTALLATION MANUAL 2 Figure B Power switch (ON/OFF) 1 2 Source Chassis Grounding Selector 3 Source Shield Selector5 4 Power Source S

CBX800 INSTALLATION MANUAL 20 NOTE For applications that do not use RX485 signals, do not leave these lines floating but connect them to SGND as sh

CBX800 INSTALLATION MANUAL 21 INPUTS The two optocoupled polarity insensitive inputs, Input 1 (External Trigger Input) and Input 2, a generic input,

CBX800 INSTALLATION MANUAL 22 EXTERNAL TRIGGER INPUT CONNECTIONS USING EXTERNAL POWER Pulled down to External Input Device Reference Input Signal

CBX800 INSTALLATION MANUAL 23 Power to Input Input Device Signal Input Device Reference Input Device NPN Input 2 Using CBX800 Power INPUT 2 CON

CBX800 INSTALLATION MANUAL 24 OUTPUT CONNECTIONS USING CBX800 POWER CAUTION Power is available directly to the Output Device, independently from t

CBX800 INSTALLATION MANUAL 25 OTHER I/O Two further input signals and one output signal, are available on the CBX800 for readers that support them.

CBX800 INSTALLATION MANUAL 26 INDICATOR LEDS green yellow green yellow green blue/red yellow green yellow green Figure 37 – Indicator LEDs Ther

CBX800 INSTALLATION MANUAL 27 TYPICAL LAYOUTS The following figure shows the general system layout. Figure 38 – General System Layout The gener

CBX800 INSTALLATION MANUAL 28 Fieldbus Gateway Layout CBX800 Parameters Fieldbus Gateway (ex: Profibus interface board =

CBX800 INSTALLATION MANUAL 29 Ethernet TCP/IP Gateway Layout CBX800 Parameters Ethernet TCP/IP Gateway (interface board = BM

CBX800 INSTALLATION MANUAL 3 UPDATES AND LANGUAGE AVAILABILITY UK/US The latest drivers and documentation updates for this product are available on

CBX800 INSTALLATION MANUAL 30 ID-NET™ Gateway Layout CBX800 Parameters ID-Net Gateway Note Net Type Rotary Switch 9 Addr

CBX800 INSTALLATION MANUAL 31 MUX32 Gateway Layout CBX800 Parameters MUX32 Gateway Note Net Type Rotary Switch 0 Topology

CBX800 INSTALLATION MANUAL 32 TECHNICAL FEATURES ELECTRICAL FEATURES Supply Voltage 10 to 30 Vdc* Consumption 0.8 - 0.5 A Limited Current Consu

CBX800 INSTALLATION MANUAL 33 COMPLIANCE POWER SUPPLY This product is intended to be installed by Qualified Personnel only. This device is intend

DECLARATION OF CONFORMITY 09Datalogic Automation S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that

CBX800 INSTALLATION MANUAL 4 DESCRIPTION The CBX800 is a Gateway connection box which can be used as an accessory to facilitate system connections

CBX800 INSTALLATION MANUAL 5 ACCESSORIES The following accessories are available on request for the CBX800: Name Description Part Number BM200/210

CBX800 INSTALLATION MANUAL 6 ACCESS TO INTERNAL PARTS To make installation and replacement easier, the CBX800 is made up of three parts: 1) the b

CBX800 INSTALLATION MANUAL 7 MECHANICAL INSTALLATION CBX800 can be mounted to various wooden or plastic surfaces using two self-threading screws (3.

CBX800 INSTALLATION MANUAL 8 NOTE Vdc is electrically connected to +V, just as GND is electrically connected to -V. This is useful for supplying ex

CBX800 INSTALLATION MANUAL 9 PINOUT Pinouts Group Name Function Vdc Power Supply Input Voltage + GND Power Supply Input Voltage - Input Power Eart